CAL 9500 Temperature/Process Controller

Features of the 9500P programmable process controller

Full PID Autotuning Process Controller
Total of 3 outputs. Choose from:
4-20mA
0-5v / 0-10v
SSR drive
Relay
Input options:
Thermocouple
2 or 3 wire PT100
0-50mV, 0-5, 0-10V, 0-20mA, 4-20mA
Alarms with 5 options
PID heat-cool operation
Programmer operation
Sleeve mounting for easy maintenance
IP66 protection from front panel
CE, UL & CSA approvals
3-year warranty
Charting and logging software option
RS232/485 Modbus option

Programmer Features

Up to 31 programs (profiles)
Up to 126 segments
Unlimited use of event outputs via the 2nd and 3rd outputs
Copy/paste/edit/delete functions to simplify program building
Call another program as a sub-program segment
Up to 999 program loop cycles, or continuous loop cycling
Hold back function to ensure the next segment is not started until the last segment reaches set-point
3 power fail recovery options, (hold, continue or reset)
Front Panel Interrogation of the program position
Memory usage indication during programming
Front panel 'release from hold' function to run the program.

9500P programmable process controller

1/16^th DIN 48 x 48mm

Set-point and process value shown.

Options:	Thermocouple/PT100
Inputs:	0-5, 0-10, 4-20mA (0-20-A)
Outputs:	(third is always relay) Outputs 1 & 2 a combination from: SSR driver, relay, 4-20mA, 0-5V, 0-10V
Communications:	RS232, RS485 with MODBUS RTU protocol

Inputs: (SM = sensor maximum)
Calibration accuracy:	+/- 0.25% SM +/-1°C
Sampling frequency:	input 10Hz, CJC 2 sec.
Common mode rejection:	Negligible effect up to 140db, 240V, 50-60Hz
Series mode rejection:	60db, 50-60Hz
Temperature coefficient:	50ppm/°C SM typical
Reference conditions:	22°C +/- 2°C, rated voltage after 15 minutes settling time.

Outputs: (check configuration)
SSd1 and SSd2	solid state relay driver: to switch a remote SSR 6VDC (nominal) 20mA non-isolated
Miniature power relay:	form A/SPST contacts (AgCdO)
rLY1, rLY2, rLT3:	2A/250VAC resistive load
Analog output:	4-20mA 500 ohms max’ +/- 0.1% fs
	0-5Vdc 10mA (500 ohms min’) +/- 0.1% fs
	0-10Vdc 10mA (1K ohms min’) +/- 0.1% fs

General:
Displays:	Upper, 4 digits, high brightness green LED 10.4mm (0.4") high.
	Lower, 4 digits, high brightness orange LED 9mm (0.35") high.
	Digital range –199 to 9999
	Hi-res mode –199 to 999.9
	LED output indicators – flashing SP1 square, green; SP2/SP3 round, red.
Keypad:	3 elastomeric buttons.
Power Supply:	100-240V AC, 50-60 Hz , (typ' 5.0 VA)
Environmental:
Humidity:	Max’ 80%
Altitude:	up to 2000M
Installation:	categories II and III
Pollution:	Degree II
Protection:	NEMA 4X, IP66
EMC emission:	EN50081-1 FCC rules 15 sub-part J class A
EMC immunity:	EN50082-2
Ambient temperature:	0-50°C (32-130°F)
Moldings:	flame retardant polycarbonate
Weight:	180g (6.4 oz)
Dimensions:
Front fascia:	51.0 x 51.0mm (2.0" x 2.0") (includes gasket)
Sleeve length:	106.7mm (4.2") (with gasket fitted)
Instrument body:	44.8 x 44.8mm (1.76" x 1.76")
Overall length:	116.2mm (4.57")
Cutout:	1/16 DIN - 45mm x 45mm (1.77" x 1.77") - Punches