Communications Products

• Complies with IEEE-802.3 10Base-T and IEEE-802.3u 100Base-FX standards
• Provides 4 10/100Mbps switched ports and 1 100Base-FX switched port
• Each IP port supports both 10/100Mbps auto-negotiation and auto-sensing
• Supports duplex type selector for setting the fiber port to either full or half duplex
• Full/half duplex operation for each port
• Support 1K MAC addresses and automatic MAC address learning and aging
• Store-and-forward architecture
• Non-blocking switching fabric
• Supports full-duplex flow control (IEEE-802.3x)
• Back-pressure flow control in-duplex mode
• Compact metal chassis design
• +10 ~ +30Vdc voltage or 85 ~ 230 VAC

• Automatic MDI / MDI-X crossover for plug-and-play
• Each port supports both 10/100 Mbps speed auto negotiation
• Store-and-forward architecture
• Full duplex IEEE 802.3x and half duplex backpressure flow control
• 1.4Gbps high performance memory bandwidth.
• Integrated look-up engine with dedicated 1 K unicast MAC addresses.
• MTBF = 438,000 hours( Temperature is 25 °C)
• MTBCF = 525,600 hours ( Temperature is 25 °C)
• Supports +10~+30 VDC voltage
• Supports operating temperatures from 0 ~ +70°C
• DIN rail mount for industrial usage

Spex: www.icpdas.com/products/Switch/industrial/ns-200ft.htm

• Automatic MDI / MDI-X crossover for plug-and-play
• Each port supports both 10/100 Mbps speed auto negotiation
• Store-and-forward architecture
• Full duplex IEEE 802.3x and half duplex backpressure flow control
• 1.4Gbps high performance memory bandwidth.
• Integrated look-up engine with dedicated 1 K unicast MAC addresses.
• MTBF = 438,000 hours( Temperature is 25 ℃)
• MTBCF = 525,600 hours ( Temperature is 25 ℃)
• Supports +10 ~ +30Vdc voltage
• Supports operating temperatures from -30 ~ +75 ℃
• DIN rail mount for industrial usage
• Metal Case (NS-105), Plastic Case (NS205)

Spex: www.icpdas.com/products/Switch/industrial/ns-205.htm

• Fiber Port: ST (Multi-mode)
• Wave Length: 850 nm
• Fiber Cable: 62.5/125 μm
• Speed: “Self Tuner” , auto switching baud rate, 300~115200 bps
• Extend transmission distance up to 2 Km.
• Isolation voltage: 3000Vdc
• Optical isolation: 3570Vrms
• Environment:
  Operating temperature: 0℃ ~ +70℃
  Storage Temperature: -20 ~ +85℃
  Relative Humidity: 10% to 90% non-condensing
• Dimensions: 32.30 x 99.00 x 77.50 mm (w x h x d)
• Power requirement: Unregulated +10Vdc ~ +30Vdc.     2.0W max.

Spex: www.icpdas.com/products/Industrial/communication_module/i-2541.htm

I-7520R
RS-232 to RS-485 Converter

• Input : RS-232 protocol
• Output : RS-485 protocol (two wire, D+, D-)
• Speed : auto switching baud rate, 300~115200 bps
• Internal "Self Tuner"
• Maximum of 256 modules. in a single RS-485 network without using a repeater
• Maximum of 2048 modules. in a single RS-485 network when using a repeater
• Isolation voltage: 3000Vdc on the RS-232 side
• Repeater request: 4,000 feet or over 256 modules
• Power Required: 10 ~ 30 VDC

Spex: www.icpdas.com/products/Remote_IO/i-7000/i-7520.htm

I-7561
USB to RS-232/422/485 Converter

• Full speed with USB 1.1specifications.
• Input: USB protocol.
• Output: RS-232/422/485 protocol.
• Speed: “Self Tuner” inside
• 3000 Vdc isolation protection provided.
• 256 modules max. in one RS-485 network without repeater.
• 2048 modules max. in one RS-485 network with repeater.
• Repeater request: 4,000 feet or over 256 modules.
• Plug-and-play installation.
• The I-7561 gets the power from USB port; no external power supply required
• Windows 98/ME/2000/XP and Linux drivers supported. Driver for other operating system are currently under development

Spex: www.icpdas.com/products/Remote_IO/i-7000/i-7561.htm 

I-7563
USB to 3-channel RS-485 Converter Hub

• Full speed with USB 1.1specifications.
• Input Port: USB
• Output Port: Three RS-485
• Speed: "Self Tuner" inside
• 3000 Vdc isolation protection provided
• Photo-coupler isolation: 2500V rms
• 256 modules max. (All channels)
  RS-485 network without repeater.
• 2048 modules max. (All channels)
  RS-485 network with repeater
• Repeater request:4,000 feet or over 256 modules
• Plug-and-play installation
• The I-7563 gets the power from USB port; no external power supply required
• Windows 98/ME/2000/XP and Linux drivers supported. Driver for other operating system are currently under development

Spex: www.icpdas.com/products/Remote_IO/i-7000/i-7563.htm

DIN-KA52F
DIN-KA52F: 24V/1A power supply with DIN-Rail Mounting

• Input Range: 100~250AC
• Input Frequency: 50Hz to 60 Hz
• Output: 24Vdc/1Amp max.
• Output Power: 25Watts
• Operating Temperature:0 to 70℃
• Storage Temperature : -40 to 85℃
• Dimension:
  65 x 105 x 36mm (KA-52F)
  68 x 107 x 50mm (DIN-KA52F)

Spex: www.icpdas.com/products/Accessories/power_supply/ka-52f.htm

Fiber Optic Connector Types:
ICP Fiber Products are available with the following connectors (please specify):

Pricing:
 

NS-115F Series

NS-200FT